2003 sequoia coolant engine block drain plug

2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG DRIVERS
2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG FULL
2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG SERIES
2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG CRACK

2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG FULL

This is the only full strength extended life coolant made that was available at a reasonable cost. Refilled with 2 full gallons of extended life Peak Asian red/pink concentrate. Drain coolant from Toyota Sequoia/ Tundra Engine block 4.7L. Did that half a dozen times until finally the water draining out was clean. So I did that and was able to add two gallons of water at a time. So for a few cycles of drain, fill, drive drain, I was only able to add about one gallon of water at time and the stuff draining out was not getting visibly cleaner.Ĭhecked on the Toyota forums and found that you could disconnect the oil cooler water hose at the filter, and that would drain the block better then the drain valve. Order your parts online or pick them up in-store at your local Advance Auto Parts. Check prices & reviews on aftermarket & stock parts for your 2003 Sequoia Radiator Drain Plug. Yes it had drain valves on the block, but I wasn't about to risk snapping them off on a 1/2 million mile engine and creating a much worse problem. Compare 2003 Toyota Sequoia Radiator Drain Plug brands. Turn off the engine and drain the water, fill up the radiator with antifreeze until you have a 50/50 coolant / distilled water mixture and burp the system. Fill up the radiator with distilled water and run the engine. If you are flushing the system out then just remove the thermostat (also under the car on the bottom of the engine) and flush the system out. It is on the rear of the engine between the eng.

screwed the knock sensor into the drain port on the block. When you get to the back side, the intake side, look up and you should see something that looks like a water spigot pointing downwards and a bolt attached to it pointing towards the rear of the car. SOURCE: Engine block coolant drain plug Unfortunately g.m. maybe a few ounces ended up on the driveway.Main issue was that both radiator hoses connect to the top of the engine, so draining the radiator will get nearly nothing out of the block not to mention the heater cores. This video shows where the radiator drain plug (petcock) is located on a 2002 Toyota Sequoia. You need to raise the front end and then slide underneath to get to it.

2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG DRIVERS

Last time I needed to drain coolant I got it all out and into a bucket and it was perfectly clean. Coolant block drain plug is on the drivers side if I remember correctly, above the drain pan on a portion of the block thats 45 degrees vertical (part of the V of a V-8). Same size hose fits through a hole on the front crossmember that lines up with a small nipple on the radiator petcock. Spin in the drain plug in the clockwise direction and tighten it until it is snug.

Spin In New Drain Plug: Tighten Radiator Plug: Gallon Jug - Quart Lines: Clean the drain hole on the bottom of the radiator with a small towel. This part of the operation would be WAY easier with the starter flap removed. The part number for the drain plug is Honda 19011-PH1-621 and the rubber o-ring part number is Honda 19012-671-300. Changing the coolant on a Honda: Put a bucket directly below the radiator drain plug. 2003 Toyota Sequoia Radiator Drain Plug - from 1.99+ Equip cars, trucks & SUVs with 2003 Toyota Sequoia Radiator Drain Plug from AutoZone. and it avoids having to drip down an oily/dirty frame rail and suspension. Having a forward O2 sensor block the plug only compounds the lameness of what was already a dumb design in OBDI form. I bring this hose in my trip toolkit to make collecting the coolant on the side of the road easier if needed. Filled radiator and filled reserve and ran with cap off radiator till engine heated up. Anyone know where the engine coolant drain is located I’ve heard a couple different things from different sources.

2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG SERIES

This problem just started out of now where.

impailass said: About to do a coolant flush on my 04, 3800 Series II.

cummins isc engine coolant sensor location cummins isc engine coolant. Coolant level was low (sucked reserve bottle dry). ( of 4) The 2004 Toyota Sequoia has 7 problems reported for vsc trac light.

2003 SEQUOIA COOLANT ENGINE BLOCK DRAIN PLUG CRACK

I've also found that if you can be a bit of a contortionist, once you crack the drain loose, from the top you can pull the plug and insert a vinyl hose into the hole (can't remember exact size but around 3/8' OD, maybe 5/16) to control where the coolant flows. 2003 PONTIAC AZTEK 6 CYL AWD AUTOMATIC 120,000 MILES I drove the vehicle 4-5 miles and the temp guage pegs high with no heat through the heater. this is perfectly lined up and sized to allow access to the block drain without needing to remove/break trim flap buttons. Not sure if my wheel well trim flaps are different, but on mine the flap that blocks access to the starter has a small 1' gap between the front edge and the shock tower.

2003 sequoia coolant engine block drain plug